Filter By:
- Show More Brands
- Show Fewer Brands
- Show More Sizes
- Show Fewer Sizes
- Show More Model Years
- Show Fewer Model Years
Parts & Accessories
$20.00 - $34.99
These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals.
Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.
$15.99
WTB's TCS Brass Valves are your key to the excellence that is tubeless wheels and tires. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch.
$18.99
• 5mm skewer set (F+R hubs)
• Standard 5mm Hex release
• Black or Silver anodized finish
• Chromoly axles
$3.29 - $3.50
Replacement Axle nuts for three speed Sturmey Archer hubs.
$24.99 - $27.99
- Supplies full wheel illumination for 700c/29in wheels and smaller
- Approximately 40 hrs of battery life
- Water resistant design
- Includes 3 (AA) batteries
- Sold individually (1 wheel)
- Easy to install
$17.99 - $24.99
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant.
Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads:
- MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi
- ERD 615, 622x49.9, 29 in x 52.3mm
Your rim has a stepped valve and is not compatible with this Schrader valve.
$39.99 - $48.00
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option.
Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes.
- Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles.
- Low Profile—No more bulky handles to strike trail obstacles or create wind drag. Aerodynamic design.
- Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength.
- Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal.
- Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
- The axle is precision CNC-machined in the USA from 7075 aluminum and hard-anodized for rugged durability. Our axles are built to the tightest standards in the industry.
- No special tools required. Design allows for wheel installation and removal using your standard 6mm hex wrench.
- Designed, built, and quality tested in the USA. Proven around the world.
$54.99 - $65.00
Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure.
Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more.
- The axle shaft and axle end are precision CNC-machined.
- The axle shaft is 7075 aluminum and hard black-anodized for rugged durability.
- The stainless steel axle end allows for mounting of the hitch provided with your trailer.
- Hardware for attachment of the hitch is included; the hitch, itself, is not.
- No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench.
- Designed, built, and quality tested in the USA. Proven around the world.
$48.00 - $59.99
After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option.
Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes.
- Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles.
- Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design.
- Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength.
- Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal.
- Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.
$49.99 - $74.99
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season.
- When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out.
- The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability.
- No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench.
- Designed, built, and quality tested in the USA. Proven around the world.
Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$26.99
Thru-Axle hub adapters allow the use of 100 mm front thru-axle hubs in 100 mm QR forks.
-Allows the use of modern thru-axle wheels in forks designed for quick-release compatible hubs
-100 mm front hub spacing only
-CNC-machined AL-6061
$5.99 - $7.99
- Flanged 15mm axle nuts
- Durable chromoly construction
- Spacing / Axle: B/O
$6.99 - $7.99
- Flanged 15mm axle nuts
- Durable chromoly construction
- Spacing / Axle: B/O
$22.99
Converts CenterLock hubs to accept 6-bolt rotors
- Available for standard Quick Release as well as Thru-Axle hubs
- Extruded alloy collar with CNC shoulder pins and lock ring
- Eliminates the need for rotor bolts
$9.99 - $10.99
- High-quality fat bike rim strips
- Super durable PVC material
$16.99
On today's MTB frames, there are many diameters and width dropouts standards. Most Mavic wheels can be fitted with specific adapters to match with those frames: 142mm extenders for ITS-4 hubs, 142 mm extenders for TS-2 hubs and QR adapters (delivered with a front quick release) for all of them.
- Converts a 12mm rear axle to fit in a frame with 9.5mm dropouts
- Requires one pair per hub
$22.99
On today's road forks, there are multiple front axle standards. Mavic front axle adapters allow you to mix and match without replacing wheels/forks. Most Mavic wheels can be fitted with specific adapters to match your fork end dimensions.
- Adapts Mavic road wheels to use 12mm front axle
- One pair is required for each hub to be converted
$26.99
On today's raod forks, there are multiple front axle standards. Mavic front axle adapters allow you to mix and match without replacing wheels/forks. Most Mavic wheels can be fitted with specific adapters to match your fork end dimensions.
- Converts Mavic front hubs to 9mm
- One pair required for each hub to be converted
$22.99
On today's MTB frames, there are many dropout diameter and width standards. Most Mavic wheels can be fitted with specific adapters to match your wheelset with your frame.
- Converts Mavic mountain hubs to quick release
- One pair is required for each hub to be converted
$39.99
If wheel theft could be a problem, then these high-grade locking skewers and nuts will challenge even the most determined thieves. The KnoxNut features a one-of-a-kind nut protected by a super-tough free-floating outer ring, making it impossible to release your wheel with anything other than the special key.
KnoxNuts can be installed on existing skewers or combined with the KnoxNut Skewer, a unique and unobtrusive blind-head cromoly skewer.
The special forged key is lightweight and easy to carry. Use with regular 6mm allen key to unlock. All keys are marked with a unique serial number and replacement keys are only sold to consumers that have previously registered a key on deltacycle.com.
Set Includes:
- Front blind-head skewer with KnoxNut
- Rear blind-head skewer with KnoxNut
$14.99
Tubeless valves for DT Swiss rims for repair or replacement.
- DT Swiss Narrow Base Tubeless Valve - 53mm
$16.99
Tubeless valves for DT Swiss rims for repair or replacement.
- DT Swiss Narrow Base Tubeless Valve - 73mm
$49.99
When mounting a wheel quickly and safely, the RWS system is untouchable. It combines the fast mounting of a conventional quick release with the force and safety of a fitting. The high-precision toothing at the inside of the lever allows you to fully tighten the axle and perfectly position the lever.
- Ratcheting system tightens skewers with turns rather than a cam
- Lever can be rotated into an ideal position after tightening
- Removable, plug-in lever design is streamlined and protects your RWS lever
$59.99
Trainer ready.
Keep the ride going by putting your Cannondale on a trainer with the 2-in-1 trainer axle.
Where it thrives:
The open road, on the trainer
What it's built for:
Versatility, convenience
Highlights:
- Fit your Cannondale road bike to any indoor trainer Removable end caps for outdoor riding
- Compatible with Cannondale road bikes that utilize Speed Release dropouts
$12.99
- Plastic spoke covers in a variety of colors
- 300mm cut to fit length
- 36 pieces - enough for one wheel
- Increases visibility and demands attention
$24.00
Zipp 101 XPLR MOTO Rim Strip And Tubeless Tape Kit (includes rim strip and tubeless tape for 1 wheel).
$151.00
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation.
The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included.
- 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center
- Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels
- Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels
- Includes cassette spacer
- Material: Aluminum
$70.00
- Wheel bearing kit front/rear
- Bearing dimensions: 17 x 30 x 7mm
- Material: steel
- 2 pieces
$19.00 - $31.00
Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.
Page 1 of 10
Next page